Concrete cutting in Spring Hill TN - clean, straight cuts right where you want them
Need a slab opened for a pipe, a doorway or a new walkway? We cut straight lines where you choose and leave clean edges.
- Licensed and insured.
- Free on-site estimates.
- We respond within 1 business day.
How do you cut out a section of concrete without cracking the rest?
Concrete cutting in Spring Hill means sawing straight lines or openings through a slab or wall, so you can take out a section, run a trench or add an opening without breaking the concrete you're keeping.
Most calls start with something that has to get through concrete that's already there, like a new drain line, a cracked panel in a driveway that needs replacing or a slab in the way of an addition. The price moves with how many feet we cut, how thick the concrete is, whether there's steel in it, whether we're cutting a floor or a wall and whether you want the pieces hauled off. The schedule mostly depends on the permit question and, for structural concrete, the scan that has to happen first. The estimate I write on site spells all of that out for your job.
When does a slab need cutting instead of a full tear-out?
One panel sank or cracked
When one section of driveway or patio has dropped or split and the rest is sound, the dirt under that piece usually settled or washed out. Cutting along a straight line lets us take out just that piece, and the longer it sits, the more water gets under it and the more the edges chip.
A pipe under the slab
A slow drain, a damp spot or a plumber telling you the line runs under the floor usually means someone has to get through the concrete. A clean saw-cut trench gives them room to work and a straight edge to patch against, where a jackhammer tends to crack the floor you're keeping.
Concrete in the way
A slab where you want an addition, a wider driveway, a doorway or a new walk means part of it has to go. Breaking it out by hand usually sends cracks into the part you meant to keep, so setting a cut line first costs less than fixing that damage later.
How we handle concrete cutting
Before we cut, we agree on where the line goes, how deep it runs and whether you want the pieces hauled off or left in place, because sawing and removal are two separate jobs and your estimate should say which you're getting. Then we pick the saw for where the cut sits and how thick the concrete is. Structural concrete and post-tensioned slabs, the kind with steel cables pulled tight inside them, get a scan before the first cut so we know where the rebar, the steel bars that hold a slab together, sits along with any tendons, conduit or pipes. On a basement or structural cut, we plan the saw and how it's powered ahead of time, and we keep the slurry, the gray mix of water and concrete dust that comes off the blade, contained. Then we cut, check the edges and haul the pieces off if that was part of the job.
Cutting is often the first half of a bigger job. When we take out a sunken panel or widen an apron, the new section is concrete driveway building work, and the dirt under it gets dug out and packed before anything is poured. Extending a slab out back or replacing a broken piece is concrete patio construction, where we check which way the water runs so the new section falls away from the house. If the budget gets tight, I'd rather spend your money on that base than on a fancy finish, because the base is what keeps the new piece from settling next to the old one.
Flat sawing
For driveways, patios, garage floors and other slabs, where the blade runs along the ground. Most homeowner cuts fall here, from taking out a cracked panel to opening a trench for a pipe.
Wall sawing
For walls and steep surfaces, like opening a doorway or window in a basement wall. The saw runs on a track fixed to the wall, which keeps a tall cut straight.
Hand sawing
For tight spots a bigger saw can't reach, like a corner against the house or a short cut by a step. It suits small, careful cuts more than long runs.
Wire sawing
For very thick or heavily reinforced sections that a blade can't get through. Few homeowner jobs need it, and I'll tell you at the estimate if yours does.
Get a free on-site estimate for your concrete cut
We reply within one business day to set a time, and I come out myself to measure and write the estimate. It's free, and there's no pressure to book.
Call (931) 486-8126- Based in
- Spring Hill, TN 37174
- Hours
- Mon–Fri: 6 AM–9 PM, Sat–Sun: 8 AM–10 PM
What happens when you call us to cut concrete in Spring Hill?
Here's how a cutting job runs from your first call to the final walk-through, and who you'll be dealing with at each step.
Call or send the form
Tell us where the cut goes, what you're cutting through, a rough length and whether you want the pieces hauled off. We'll set a time for me to come look.
I measure and write it up
I come out myself, measure, look at how water moves on the property and ask how you plan to use the space. The estimate spells out the cut, the depth, the saw and whether removal is included, so you know what the price covers before you agree to anything.
We settle permits and lines
Before we start, we check the permit question with the office that covers your address. I check the cut lines, and if new concrete goes back in, I check the base, forms and control joints, the cuts that tell cracks where to go, before a truck is called.
Walk the finished job together
When the cutting is done and any new concrete has cured, the wait while it hardens enough to use, we walk it together. You see the edges up close, and if something isn't right, that's the time to tell me.
Why Spring Hill homeowners call Complete Spring Hill Concrete to cut concrete
The owner writes your estimate
I come out to look at the job and write the estimate myself, and I run the crew on pour day. The person who measured your job is the one making sure it gets done the way it was written.
In business since 2021, trained old-school
I learned under a finisher who'd make me pull a form and reset it if it was off by a hair, and I've run this business since 2021. That habit is why I check a cut line twice before a blade touches it.
Covered when the city asks
Spring Hill's residential permit application asks for a contractor license and insurance on jobs of $25,000 and up, along with the contractor's Tennessee license number. We're licensed and insured, so if your cut turns into a bigger rebuild, that part of the paperwork is already covered.
Have the cut location, the surface, a rough length and whether the pieces stay or go ready, then request your estimate or call (931) 486-8126.
Concrete cutting, driveways and patios in Spring Hill
Spring Hill Development Services handles permits for development work in the city, and its engineering list names driveway extensions, open cuts, land disturbance and right-of-way work, not concrete cutting on its own. That list doesn't settle whether your cut needs a permit, and a cut that's part of a driveway extension or reaches toward the street is the kind worth asking about. We find out which office covers your address, city or county, and handle the paperwork when the job needs a permit. Nothing gets cut until that's settled, because the city doubles the permit fee when work starts without one.
We're based in Spring Hill, and most cutting calls here come from homeowners widening a driveway, stepping a patio out or getting a plumber under a garage or basement slab. On newer lots the concrete often runs tight to the house, so before I mark a line I look at where the water will go once that piece is gone. We see the same jobs in Franklin and Columbia, along with Brentwood and other cities around Spring Hill.
Questions about concrete cutting in Spring Hill
Call (931) 486-8126How much does concrete cutting cost in Spring Hill, TN?
Professional saw cutting of concrete slabs usually runs about $4 to $15 per linear foot across the US, which is the market's range for the cut itself and not our price. Reinforced or deeper slabs and wall sawing tend to cost more per foot than an easy-to-reach slab, and on a small job a minimum or trip charge can matter more than the per-foot rate. The estimate I write on site gives you the figure for your cut.
Will a concrete cutting company haul away the cut pieces?
Not always, because sawing concrete and removing it are separate jobs, and some cutters cut the lines and leave the panels where they sit. If you want the pieces gone, make removal part of the plan from the start so it's in the price you're comparing.
How do I get a round hole cut in concrete for a pipe or drain?
Round holes for pipes, drains, conduit and mechanical lines are normally core drilled, not saw cut. A core drill bores a clean circle through a slab or wall, which a straight blade can't do. Tell us the pipe size and where it has to go when you call.
Is it safe to cut concrete inside a basement?
It can be, as long as the saw's power is settled before work starts, because a gas-powered saw indoors puts carbon monoxide into a closed space. Ask any cutter how their saw is powered for an indoor job. It's a planning step, and it's one of the first things we settle on a basement cut.
What is the best way to keep dust down when cutting concrete?
Water at the blade is the usual answer, and the federal safety rule for walk-behind saws calls for a built-in system that feeds water to the blade the whole time it cuts. You can ask whether a crew's saw has one. That water turns into slurry, so also ask before the job whether it'll be vacuumed up and contained.
How do I get my house ready for a concrete cutting crew?
Clear furniture, vehicles, stored things and loose debris out of the work area before the crew arrives. If the crew has asked to use your power or water, keep the outlet and the spigot easy to reach.
Concrete work that often follows a cut
Concrete driveway building
When the cut opens up a section of driveway, we pour the replacement on a dug-out, packed base built to sit flush with the old panels.
Concrete patio construction
If you're enlarging a patio or replacing a cracked section out back, we form and pour the new slab with water running away from the house.
Concrete cutting service areas around Spring Hill
Complete Spring Hill Concrete is based in Spring Hill, TN, and the seven cities below each have their own page, including Franklin and Columbia. They aren't the only places we work, so call if your address isn't listed.
Spring Hill, TN
Get your concrete cut marked and priced
Settling the cut, the depth and the cleanup before your plumber or builder is scheduled keeps everyone working off the same line.